Garmin GPSMAP 60Cx Instruction Manual

The Garmin GPSMAP 60Cx is a rugged, waterproof handheld GPS receiver featuring a high-sensitivity GPS receiver, a color TFT display, a microSD card slot for detailed mapping, 64 MB of internal memory, a built-in basemap, and support for optional MapSource mapping software. It is designed for outdoor navigation, offering track logging, waypoint management, route planning, and compatibility with Garmin's extensive mapping products. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: High-sensitivity GPS receiver, Color TFT display, MicroSD card slot, USB port, Rocker keypad, Page buttons, Power button, External antenna connector.

Installation

Unpack and inspect contents. Install batteries and optional memory card.

1. Install batteries: Open battery compartment on back, insert two AA batteries (alkaline or NiMH recommended).
2. Install microSD card (optional): Insert card into slot under the battery cover.
3. Attach wrist strap (optional): Thread through loop on top of unit.
4. Power on: Press and hold POWER button.

WARNING! Use only recommended batteries. Ensure battery compartment is securely closed, especially before exposure to moisture.

First-Time Setup

Power on the unit; follow on-screen prompts for initial configuration.

1. Acquire satellite signals: Go outdoors with a clear view of the sky. The unit will automatically begin searching for satellites.
2. Set language: In the Main Menu > Setup > System, select your preferred language (default is ENGLISH).
3. Set units: In Setup > Units, choose between Metric, Statute, or Nautical units.
4. Calibrate compass (if using electronic compass model): Follow on-screen instructions.
5. Load maps (optional): Use MapSource software on your computer to transfer detailed maps to the microSD card.

CAUTION! Initial satellite acquisition can take several minutes. Be patient and remain stationary.

Specifications

• Display: 2.6-inch diagonal, 256-color TFT, 176 x 220 pixels.
• GPS Receiver: High-sensitivity, WAAS-enabled.
• Memory: 64 MB internal, microSD card slot (expandable).
• Battery Life: Up to 18 hours (typical use with two AA batteries).
• Interface: USB (high-speed), serial (for legacy NMEA output).
• Waterproof: IPX7 standard.
• Waypoints: 1000 with name and graphic symbol.
• Routes: 50 reversible routes with up to 250 points each.
• Tracks: 10,000 points total; 20 saved tracks.
• Operating Temp: -15°C to 70°C (5°F to 158°F).

Controls and Settings

Access functions via the Page buttons and the Rocker keypad. Main Pages: Map, Compass, Trip Computer, Highway, Main Menu.

Key Controls: POWER (On/Off/Backlight), PAGE (cycle pages), ROCKER (navigate menus/map, enter data), ENTER/MARK (confirm selection or mark waypoint), QUIT (go back).

Main Menu: Access to Waypoint Manager, Route Planner, Track Manager, Setup (System, Display, Time, Units, Heading, Interface, Tones). Map Setup: Adjust detail, orientation (North Up/Track Up), data fields. Trip Computer: Customize data screens for speed, distance, time, etc.

Connecting Devices

USB: For computer connection and data transfer. Serial: For NMEA output to autopilots or other devices. External Antenna: For improved reception in vehicles or under dense cover.

1. Turn off the GPS unit before connecting cables.
2. Connect USB cable to computer and to the GPSMAP 60Cx's port.
3. Select "USB Mass Storage" mode on the GPS unit when prompted to transfer map/data files.
4. For external antenna, screw the antenna cable into the external antenna connector on the top of the unit.

Tip: Ensure the USB cable is fully seated. Use the Garmin USB drivers if connecting to a PC for the first time.

Using Maps & Navigation

Supports Garmin MapSource topographic, marine, and street maps.

1. View Map: Press PAGE to reach the Map page. Use the ROCKER to pan the map.
2. Mark a Waypoint: Press and hold ENTER/MARK. Edit details and press ENTER to save.
3. Navigate to a Waypoint: From the Main Menu, select "Find" > "Waypoints". Select a waypoint and choose "Go To".
4. Follow a Route: Main Menu > Routes. Select a route and choose "Navigate".
5. View Trip Data: Press PAGE to cycle to the Trip Computer page.
6. View Satellite Status: Main Menu > Satellite page shows signal strength and position.
7. Save a Track: Main Menu > Tracks > Save Track.
8. Change Map Detail: Menu from Map page > Setup Map > Detail.

WARNING! Always carry a paper map and compass as a backup. GPS signals can be blocked or reflected by terrain.

Accessibility Features

Display Contrast and Backlight: Adjustable in Setup > Display for improved visibility in various lighting conditions. Audible Alerts: Can be enabled/disabled for proximity waypoints and other events in Setup > Tones.

Care & Cleaning

Turn unit off and remove batteries before cleaning. Use a soft, damp cloth with mild soap. Do not use solvents or abrasive materials.

CAUTION! Do not submerge the unit while the battery cover is open. Ensure all seals are clean and intact for waterproofing.

Regulatory Information

FCC Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that it does not cause harmful interference. Contains FCC ID: IPH-00609. Copyright © Garmin Ltd. or its subsidiaries. For support, visit www.garmin.com/support or contact Garmin Product Support in your region.

Troubleshooting

Reset: To perform a master reset (erases all user data), turn unit off. Press and hold PAGE + ENTER + POWER simultaneously while turning on. Release buttons after the second beep.

Service: Contact Garmin Product Support. Do not attempt to open the unit, as this voids the warranty.